Counterfeit components never enter a build through a well-fed supply chain. They arrive when demand outruns authorised capacity — when a line is down, a customer is screaming, and the only listing for that microcontroller sits on a broker site with a photograph that looks slightly wrong. Allocation is the counterfeiters' harvest season.
The economics are brutal and simple. An authorised distributor cannot sell what the manufacturer will not ship, so the production planner searches the grey market: brokers, independent distributors, excess-inventory resellers. Most of what trades there is legitimate surplus. Some of it is not, and counterfeiters price accordingly — high enough to seem genuine, low enough to beat the waiting list.
Once that part is soldered onto a board and the board is inside a vehicle or an aircraft, the cost of a bad purchasing decision multiplies by orders of magnitude. Every control described below exists to intercept the part before it reaches the reflow oven, because afterwards the only options are containment and teardown.
How shortage and obsolescence open the door
When a part goes on allocation or its manufacturer issues an end-of-life notice, the open-market price spikes and every drawer of recovered, remarked and recycled stock becomes economically worth laundering. Obsolescence compounds the pressure: consumer electronics churns silicon generations every few years, while industrial, automotive and aerospace programmes run for fifteen, twenty-five, sometimes forty years.
When a component is discontinued, the aftermarket demand persists, the authorised channel dries up completely, and the only remaining supply circulates second-hand. That vacuum is where remarking operations thrive — taking a mundane part, grinding off the top mark, and printing a faster grade, a wider temperature range, or a military designation on the package.
Across two decades in automotive and aerospace, I have never seen a counterfeit enter through a well-controlled channel; I have seen several enter through an emergency purchase made under schedule pressure. The pattern is consistent enough to design against: the control point is not the test lab, it is the purchase-order approval gate.

What actually gets counterfeited
The taxonomy of counterfeits tells you what to test for. The commonest category is the remarked part: a functionally similar device recovered from scrap boards, cleaned, blacktopped and re-marked to resemble a higher grade. A commercial op-amp becomes an automotive-grade one. A 16 MHz crystal becomes 25 MHz. The part may even work — at room temperature, on the bench, for a while.
Second is the rejected or substandard component diverted from the legitimate stream: factory rejects, devices that failed final test, units pulled from lots quarantined for drift. They carry genuine marks and pass visual inspection because they are genuine; they simply should have been destroyed. Third is the empty or counterfeit-die package — a plastic body with correct markings and no functional die, or a die from an entirely different product line.
Fourth is used product resold as new: pulled from decommissioned equipment, leads re-tinned, date codes refreshed. Each failure mode differs. Remarked parts fail at temperature extremes. Diverted rejects drift out of spec after months in service. Empty packages fail at power-on. Pulled parts fail through solder-joint damage, moisture-sensitivity violations and broken bond wires. Detection must therefore combine visual, electrical and structural methods — no single screen catches all four.
Counterfeit categories and their failure signatures
Counterfeit type
- Remarked scrap-board recovery
- Diverted factory rejects
- Empty or wrong-die package
- Used parts resold as new
How it fails
- At temperature extremes the die was never qualified for
- Stochastically, drifting out of spec in service
- Immediately at power-on, unless the circuit tolerates it
- Bond wire and solder damage from desoldering heat
Authorised distribution as the first line of defence
The single most effective control is also the least glamorous: buy from traceable, authorised sources and treat any exception as a formal risk event. Authorised distribution means the distributor holds a contract with the component manufacturer, receives product through the manufacturer's logistics chain, and passes certification, date-code traceability and change notifications downstream. Franchised distributors also handle moisture-sensitive packing correctly and carry the manufacturer's warranty.
When authorised supply fails, the discipline shifts to documenting the exception. A written approval gate before any broker purchase should require: a named broker, full traceability chain back to a previous authorised owner, certificates of conformance that can actually be verified, and photographs of packaging and labelling before the shipment is opened. The paperwork itself is a screening tool — counterfeit certificates collapse under a single phone call to the original manufacturer asking whether that lot number exists.
Be suspicious of excess-inventory resellers claiming to be "authorised" by association membership. Trade association membership is not a franchise agreement. Ask which manufacturer appointed them, for which product lines, and get it in writing. Verify the shipping documentation: genuine authorised stock arrives with the manufacturer's own packing labels, moisture barrier bags with humidity indicator cards, and correct dry-pack dating. Product that arrives loose in anti-static bags with photocopied labels has already told you something.
Non-destructive examination first
Every suspect lot should pass through a documented incoming inspection regime before anything touches a reel feeder. Start externally. Examine the package body under 30× to 100× magnification for re-marking evidence: ghosting of previous legends, uneven font geometry, ink that smears with a gentle solvent rub, or surface texture that differs from a known-good sample. Blacktopping often shows as a matte layer that fractures at package edges or around the pin-one chamfer.
Lead inspection is next. Re-tinned or recovered leads show solder bloom, dull finishes, uneven plating, straightened pins and tooling marks from desoldering. Compare lead pitch and coplanarity against the datasheet and a gold sample. Check the date code: a two-week-old date code on a part allocated for eighteen months is not a bargain, it is a warning. Country-of-origin and lot markings must be internally consistent across label, box and body.
Dimensional checks catch cloned packages: measure body width, lead span and standoff against the datasheet with calipers or an optical comparator. Weighing samples on a precision balance is crude but effective — counterfeiters rarely match moulding compound density, and a weighed sample set compared against known-good reference often separates populations immediately. X-ray fluorescence verifies lead finish composition against specification.
Internal structure needs X-ray radiography. Look for die size versus package outline, wire bond count and geometry, voiding in the die attach, and whether the die pattern matches the genuine article. Empty packages announce themselves instantly under X-ray. A die of the wrong size or a bond layout inconsistent with the manufacturer's design tells you the part came from a different product line, however perfect the exterior looks.
Decapsulation and destructive analysis
When non-destructive methods leave doubt, decapsulation settles it. Chemical decapsulation — typically fuming nitric or sulphuric acid, or plasma for delicate structures — opens the package to expose the die. Under a metallurgical microscope you read the die itself: manufacturers laser-mark die with part numbers, revision codes, copyright dates and fab identifiers. If the die says something different from the package, the lot is counterfeit, full stop.
Cross-sectioning takes the analysis further. Polishing a mounted sample through the die stack reveals die attach quality, bond wire diameter and composition, and the layer structure of the die itself. Cloned devices often show visibly different metallisation patterns, older process geometries, or missing passivation features compared with a genuine reference. For suspect passives, cross-sectioning reveals ceramic body structure and termination plating layers that differ from the qualified part.
Destructive electrical verification completes the picture. Curve tracing on a sample basis exposes die substitutions that function roughly but not identically to a gold sample. Full characterisation across temperature, per the datasheet limits, catches grade jumping: a commercial part re-marked as automotive will frequently fail at the cold end of -40 °C or drift beyond specification at high temperature.
A hundred per cent external inspection catches re-marking but not die substitution; destructive tests cannot run on the whole lot.
Sampling philosophy therefore matters. Define statistically defensible, AQL-based sampling for destructive analysis, quarantine the remainder until results clear, and never let a suspect lot touch production while tests are pending. Lines built and shipped on "provisional" acceptance are a pattern I have seen unwind more than once; the recovery costs far more than the delay ever would have.
Suspect-lot handling sequence
- 01Approval gateBroker purchase requires written exception with traceability chain
- 02External inspectionMagnification, leads, date codes, dimensions, weight, XRF
- 03X-ray radiographyDie size, bond geometry, voiding versus genuine reference
- 04Destructive samplingDecapsulation, cross-section, curve trace on AQL sample
- 05DispositionRelease, reject or report to manufacturer and reporting bodies
Defending against obsolescence systematically
Because obsolescence creates the counterfeit opportunity, obsolescence management is counterfeit prevention. Maintain a live component lifecycle database for every part in every product. Manufacturer EOL notices, PCN bulletins and last-time-buy deadlines must reach an engineer who acts on them, not a shared mailbox. When a critical component approaches discontinuation, decide deliberately: last-time-buy with storage controls, qualified redesign, or an approved alternate — not an emergency broker search in year nine of a fifteen-year programme.
Long-term storage of last-time-buy stock has its own discipline. Moisture-sensitive devices stored for years still carry floor-life clocks; bake and dry-pack procedures per J-STD-033 apply when the stock is finally drawn. Track storage conditions and shelf age so genuine stock is not discarded and then replaced through grey-market purchases. Your own warehouse mismanagement becomes the counterfeiters' customer acquisition channel.
Where genuine last-time-buy is impossible, qualified aftermarket sources exist — firms that redesign form-fit-function replacements or maintain certified re-manufacturing under controlled conditions. The distinction between these and a broker with a stock list is the audit trail: certified sources will show you their processes, traceability and test regimes. Anyone who refuses an on-site audit of the facility supplying flight-critical or safety-critical components has answered your question.
Building the response into your quality system
Incoming inspection for suspect lots must be a documented, trained procedure with defined acceptance criteria, not an engineer's improvisation. Reference the industry frameworks — AS6081 for risk mitigation in distribution, AS5553 for the buying organisation, AS6171 for test methods — and write your internal procedure against them. Train receiving inspectors on the visual tells: blacktop texture, re-tinned leads, inconsistent marking fonts, wrong packaging. Give them authority to quarantine without negotiation.
Traceability downstream is your containment insurance. If a counterfeit is found in finished stock, you must be able to identify every assembly built with that lot. Lot-controlled issue to production, retained reel identity and purchase-order-to-serial-number linkage cost little day to day and are worth everything on the day it goes wrong. Establish a reporting route to the manufacturer and relevant reporting bodies so confirmed counterfeits do not simply return to the market through another broker.
Finally, close the loop on behaviour. The organisation that punished a planner for stopping a line taught everyone to keep buying from brokers quietly. The organisation that treats an authorised-source exception as a formal, reviewed, time-boxed risk decision keeps the pressure where it belongs — on finding genuine supply. Counterfeiters do not defeat technology; they defeat urgency. Your defence is making it procedurally easier to pause than to substitute.
